What is Pipe Joint? | Pipe Joint

What is Pipe Joint?

Pipe joints are integral to any piping system because it is not possible to have a continuous length of pipe for a pipe network. These joints can make or break a pipeline system depending on the resulting durability of the technique used to form the joint.

There are different materials of pipes use in the pipeline industry depending on the need and the type of product that will be conveyed through the pipe.

Types of Pipe Joints

The pipes usually connected to vessels from which they transport the fluid. Since the length of pipes available limited, therefore various lengths of pipes have to join to suit any particular installation. There are various forms of pipe joints use in practice, but the most common of them discussed below.

Different types of pipe joints used in plumbing system are as follows.

Socket or a coupler joint

The most common method of joining pipes is by means of a socket or a coupler. A socket is a small piece of pipe thread inside. It screwed on halfway on the thread end of one pipe and the other pipe then screwed in the remaining half of the socket. In order to prevent leakage, jute or hemp wound around the threads at the end of each pipe. This type of joint mostly used for pipes carrying water at low pressure and where the overall smallness of size is most essential.

Types of pipe joint

Nipple joint

In this type of joint, a nipple which is a small piece of pipe threaded outside screwed in the internally threaded end of each pipe. The disadvantage of this joint is that it reduces the area of flow.

Union joint

In order to disengage pipes joined by a socket, it is necessary to unscrew pipe from one end. This is sometimes inconvenient when pipes are long. The union joint, provide the facility of disengaging the pipes by simply unscrewing a coupler nut.

Spigot and socket joint

It is chiefly used for pipes which are buried in the earth. Some pipe lines are laid straight as far as possible. One of the important features of this joint is its flexibility as it adopts itself to small changes in level due to settlement of earth which takes place due to climate and other conditions. In this type of joint, the spigot end of one pipe fits into the socket end of the other pipe. The remaining space between the two is filled with a jute rope and a ring of lead. When the lead solidifies, it is caulked-in tightly.

Expansion joint

The pipes carrying steam at high pressures usually joined by means of expansion joint. This joint is used in steam pipes to take up the expansion and contraction of pipelines due to changes in temperature. In order to allow for a change in length, steam pipes are not rigidly clamped but supported on rollers. The rollers may be arranged on wall brackets, hangers or floor stands. The expansion bends are useful in a long pipeline. These pipe bends will spring in either direction and readily accommodate themselves to small movements of the actual pipe ends to which they are attached.

Flanged joint

It is one of the most widely used pipe joints. A flanged joint may be made with flanges cast integral with the pipes or loose flanges welded or screwed. Two cast-iron pipes with integral flanges at their ends. The flanges are connected by means of bolts. The flanges have seen standardized for pressures up to 2 N/mm2. The flange faces are machined to ensure the correct alignment of the pipes.

The joint may be made leakproof by placing a gasket of soft material, rubber, or canvass between the flanges. The flanges are made thicker than the pipe walls, for strength. The pipes may be strengthened for high-pressure duty by increasing the thickness of the pipe for a short length from the flange. For even high pressure and for large diameters, the flanges are further strengthened by ribs or stiffeners. The ribs are placed between the bolt holes.

Hydraulic pipe joint

This type of joint has oval flanges and are fastened by means of two bolts. The oval flanges are usually used for small pipes, up to 175 mm in diameter. The flanges are generally cast integral with the pipe ends. Such joints are used to carry fluid pressure varying from 5 to 14 N/mm2. Such high pressure is found in hydraulic applications like riveting, pressing, lifts, etc. The hydraulic machines used in these installations are pumps, accumulators, intensifiers, etc.

Scroll to Top