What is a Twist Drill Bit?

What is a Twist Drill Bit?

Twist drills are the most common and easiest way to put a hole in steel, wood, or other non-ferrous materials with a drill bit but with so many options to choose from it is important that you use the correct one for your specific application. Doing so will increase production, lower operating costs, and provide you with the exact finish you are looking for.

Twist drills are rotary cutting tools that normally have two cutting edges and two flutes which are grooves formed in the body to provide cutting lips, to permit the removal of chips, and to allow coolant or cutting fluid to reach the cutting action.

Twist drills (also commonly referred to as twist bits) are the most widely used of all drill bit types; they will cut anything from wood and plastic to steel and concrete. They are most frequently used for metal cutting, so they are generally made from M2 high-speed steel.

At diameters up to about 1/2″, twist drills are not only the cheapest of all bits a woodworker could use, they offer the widest selection of sizes. Although they are designed for cutting metal, they will work quite well in wood, if sharp. This generally means that they have not been used to cut hard materials such as steel.

A twist drill is a metal rod of a specific diameter that has two, three, or four spiral flutes running most of its length. Two-flute drills are for primary drilling, whereas three- and four-flute drills are only for enlarging cast or punched holes in a production situation.

The section between the two flutes is called the web, and a point is formed by relief grinding the web to an angle of 59° from the drill’s axis, which is 118° inclusive. This forms a sloped cutting edge at the edge of the flute, which is called the lip.

A twist drill is very inefficient at the point because the web leaves scant exit space for debris (called swarf) and because the point has a low surface speed compared to the periphery. For this reason, a good scheme for drilling larger holes is to first drill 1/4″ or less and then follow with the drill of the desired diameter.

In addition to creating the cutting lips, the flutes provide a place for the swarf to be drawn out of the hole. The spiral expedites this, but the flute becoming impacted with the swarf is always a niggling problem. For this reason, a twist drill must be constantly cleared; that is, completely withdrawn from the hole.

If you do this frequently, the swarf will be flung away, but if you wait too long, you will have to stop the drill and manually clean the flutes. The clearing is much easier with a drill press than with a drill motor.

Wood is a poster child for quickly imparting a twist drill, so even more frequent clearing than with metal is necessary. This problem can be somewhat ameliorated by now and then applying wax or spraying silicone to the drill.

Normal length drills, such as come in the average assortment, are called jobber length. If a longer drill is needed, a good hardware shop will offer an aircraft or extra-length drill. If a shorter twist drill is desired, it is referred to as a screw-machine drill. Twist drills are offered in solid carbide and carbide-tipped as well. Carbide-tipped is the choice for drilling concrete.

While it is possible to sharpen a twist drill by eye at a bench grinder, a jig or dedicated machine is necessary if out-of-the-box accuracy is to be restored. Here we have two dedicated machines.

Twist drills are difficult for users to sharpen. Great lengths are taken during manufacturing to have the lips at the same vertical height and angle. If the resulting point is not perfectly centered, and each lip does not cut a chip of equal width and thickness, the drill will wander and you will end up with an oversize hole that may not be straight either.

twist drill

While a skilled machinist can sharpen a twist drill by eye on a bench grinder, it will only do non-critical work thereafter! Only a drill sharpening jig or a dedicated machine will restore, new out of the box, accuracy to a dull drill.

The attack angle of a twist drill is controlled by the rate of twist of the flute. Drills are generally manufactured for cutting steel, which happily works out well for wood as well. This is far too aggressive for nonferrous metals such as brass and copper, which like a 5° negative rake angle.

Breakout as the drill exits the material on the far side is particularly troublesome and commonly results in the workpiece spinning on the drill press table or the drill motor spinning in the operator’s hands. Either can result in severe injury. This dangerous situation can be almost completely overcome by creating a small flat on the lip that is parallel to the axis of the drill.

Called lipping, it turns an unpredictable beast into a gentle pussy cat. What you are doing is effectively changing the rake angle of the drill to 0° instead of 15° positive. The flat does not have to be big, (1/64″ or less).

The downside of lipping is that the drill will no longer drill steel unless you sharpen the point sufficiently to remove the flat. If you only own one set of drills, that is a good reason to keep the lipping flat no larger than necessary.

Plenty of speed is the order of the day when drilling wood. You can use up to 3000 RPM for drills 1/4″ and smaller. Speed charts are readily available and it is good to have one on the shop wall. Center punching is a must if you want an accurate hole location.

Twist drills are perfect when you want a very accurate diameter hole. Say you want a press fit for a 3/16″ (.1875″ dia.) steel pin in a cabinet you are building. A #13 drill makes a .185 dia. hole, giving you a .0025 press fit for the pin.

When desiring a very accurate hole it is best to drill 1/64″ undersize, and then make the final drilling with a new, or freshly sharpened, drill of the desired diameter. If drilling a large hole this could entail three drillings: drilling 1/4″ to expedite the quick sinking of the larger hole you desire, drilling 1/64″ undersize and final drilling of the desired size.