What is a Turbocharger? – How does it work!

What is a Turbocharger?

A turbocharger, known as a turbo, is a turbine-driven forced induction device that increases the performance of an internal combustion engine by forcing additional compressed air into the combustion chamber.

This improvement over the performance of a naturally aspirated engine is due to the fact that the compressor can push more air and proportionally more fuel into the combustion chamber than atmospheric pressure alone.

A turbocharger is a device attached to a vehicle engine that is designed to improve overall efficiency and increase performance. For this reason, many car manufacturers choose the turbocharger in truck, car, train, aircraft, and construction machinery engines. They are most commonly used in Otto cycle and diesel internal combustion engines.

Who Invented the Turbocharger?

A Swiss engineer named Alfred Buchi first developed the turbocharger design in 1905 to increase the performance of diesel engines. Neat!

How Much Extra Power Can You Get?

This is the question of any transmission, and unfortunately there is no easy answer. A normal turbocharger provides network enthusiasts around 20 to 40 percent more power than standard products.

How much extra power, however, depends on a variety of variables including how big or small the turbocharger is, what changes you’ve made to the internal parts of the engine, what type of fuel you’re using, and what ECU your turbocharger setup used. Your car’s profits will vary.

How Does A Turbocharger Work?

A turbocharger is a system that helps an engine produce more power and torque through forced induction. Essentially, a turbo draws in air, cools it down, and then force-feeds the engine, more than through its standard intake port. The end result is a lot more “whee!”

A car’s turbocharger uses a principle very similar to that of a piston engine. It uses the exhaust gas to drive a turbine. This rotates an air compressor that pushes extra air (and oxygen) into the cylinders so they can burn more fuel every second.

Turbocharger

How do turbocharger work:

  1. Cool air enters the engine’s air intake and heads toward the compressor.
  2. The compressor fan helps to suck air in.
  3. The compressor squeezes and heats up the incoming air and blows it out again.
  4. Hot, compressed air from the compressor passes through the heat exchanger, which cools it down.
  5. Cooled, compressed air enters the cylinder’s air intake. The extra oxygen helps to burn fuel in the cylinder at a faster rate.
  6. Since the cylinder burns more fuel, it produces energy more quickly and can send more power to the wheels via the piston, shafts, and gears.
  7. Waste gas from the cylinder exits through the exhaust outlet.
  8. The hot exhaust gases blowing past the turbine fan make it rotate at high speed.
  9. The spinning turbine is mounted on the same shaft as the compressor. So, as the turbine spins, the compressor spins too.
  10. The exhaust gas leaves the car, wasting less energy than it would otherwise.

Parts of a turbocharger

1. The Turbine

The turbocharger turbine, which consists of a turbine wheel and a turbine housing, converts the engine exhaust gas into mechanical energy to drive the compressor. This pressure drop is converted into kinetic energy by the turbine to drive the turbine wheel. There are two main types of turbines: axial and radial flow.

2. Bearings.

The turbocharger bearing system looks simple, but it plays a key role in a number of critical functions. Some of the most important are controlling the radial and axial movement of the shaft and wheels and minimizing friction losses in the bearing system.

3. The Compressor

Compressor wheels are one of the most discussed parts of a turbocharger. The compressor section, like the turbine, consists of two main components: the compressor wheel and the compressor cover. The job of the compressor is to literally compress fresh air and direct it to the throttle body.

4. Center Housing / Rotating Assembly (CHRA)

The CHRA may not run out of ink, but it is one of the most critical parts of any turbocharger assembly. In practice, the CHRA serves as the mounting point for both housings and must be made of an essential material to handle the heat and stress on the turbine.

5. Intercooler

Understanding that a turbocharger compresses air makes it easy to see why an intercooler is important. Without doing too much math (we’re talking about the ideal gas law again), let’s just say that as pressure increases, heat is generated within a set volume.

6. Wastegates

A wastegate is simply a device that bleeds off exhaust gas before it reaches the inlet of the turbine housing.

7. Blow-Off Valves

A relief valve is essentially a pressure relief valve that is mounted on the compressor side of a turbo system. Its job is literally to release the excess boost pressure trapped in the system when the throttle blade closes.

8. Piping and Manifolds

Piping is perhaps the last thing most fans consider when building a turbo system. However, proper application and sizing are essential to ensure optimal performance. In a typical turbocharger system, the piping can be divided into three distinct sections: the manifolds, the hot side and the cold side.

Turbo manifolds, dealing with extreme temperature changes, incredible back pressure, and high loads make these areas one of the most likely areas in a turbo system to experience problems. To understand the extremes a variety must endure day in and day out, it is best to develop a variety based on longevity and strength, even if it means giving up a little bit of performance.

9. Hot Side Piping

Any piping related to the movement of the actual exhaust gas, be it to or from the turbocharger, is typically referred to as hot side piping. Due to the extreme heat generated when exhaust gases are transferred to the turbine casing, it is important to use a strong material here, and stainless steel is the material of choice for many manufacturers.

10. Cold Side Piping

The “cold side” of a turbo kit refers to any piping related to moving compressed air from the turbocharger to the throttle body. If you are installing an intercooler, it is also part of the cold side and will need to be plumbed correctly to make everything work.

Types of turbocharger

There are a number of different types of turbocharger used within the automotive industry:

  • Single-Turbo
  • Twin-Turbo
  • Twin-Scroll Turbo
  • Variable Geometry Turbo
  • Variable Twin Scroll Turbo
  • Electric Turbo

1. Single-Turbos

Single turbochargers are what most people consider turbos. Due to the different sizes of the elements in the turbo, completely different torque properties can be achieved. Large turbos provide a higher level of top-end power, while smaller turbos can spool faster and provide better low-end power.

They are an inexpensive way to increase engine power and efficiency, and as a result, they are becoming increasingly popular. They enable smaller engines to increase efficiency by producing the same power as larger, naturally aspirated engines with less weight.

However, they typically work best in a narrow RPM range and drivers often experience “turbo lag” until the turbo begins to operate within its peak RPM range.

2. Twin-Turbo

As the name suggests, twin turbos means adding a second turbocharger to an engine. For V6 or V8 engines, this can be done by assigning a single turbo to each cylinder bank.

Alternatively, a smaller turbo could be used at low speeds with a larger turbo for higher speeds. This second configuration (known as double sequential turbocharging) allows for a wider speed range and provides better torque at low speeds (reducing turbo lag), but also provides power at high speeds. Unsurprisingly, having two turbos adds significant complexity and associated cost.

3. Twin-Scroll Turbo

Twin scroll turbochargers require a turbine housing with a split inlet and exhaust manifold that couple the correct engine cylinders to each scroll. independently. For example, in a four-cylinder engine (with a 1-3-4-2 firing order) cylinders 1 and 4 can be fed to one scroll of the turbo, while cylinders 2 and 3 are fed to a separate scroll.

This arrangement allows exhaust energy to be delivered to the turbo more efficiently and results in denser and cleaner air in each cylinder. More energy is sent to the exhaust turbine, which means more power. Again, there is a cost penalty for dealing with the complexity of a system that requires intricate turbine housings, exhaust manifolds, and turbos.

4. Variable Geometry Turbocharger (VGT)

Typically, VGTs contain a ring of aerodynamically shaped vanes in the turbine housing at the turbine inlet. In turbos for passenger cars and light commercial vehicles, these vanes rotate to vary the gas swirl angle and cross-sectional area.

These internal vanes change the turbo area to radius (A / R) ratio to match engine speed, providing top performance. At low RPM, a low A/R ratio allows the turbo to spool up quickly by increasing the exhaust speed. At higher speeds, the A/R ratio increases, allowing increased airflow. This results in a low charge threshold which reduces turbo lag and provides a wide and even torque band.

While VGTs are typically used in diesel engines where exhaust gases are at a lower temperature, until now VGTs have been limited in petrol engine applications due to their cost and the requirement for components to be made from exotic materials.

The high temperature of the exhaust gases means that the vanes must be made from exotic heat-resistant materials to prevent damage. This has limited their use to luxury high performance engine applications.

5. Variable Twin-Scroll Turbocharger (VTS)

As the name suggests, a VTS turbocharger combines the advantages of a twin-scroll turbo and a turbo with variable geometry. This is done by using a valve that can divert the flow of exhaust air onto only one scroll, or by varying the amount the valve is opened, the exhaust gases can be split into both scrolls.

The VTS turbocharger design offers a cheaper and more robust alternative to VGT turbos, which means it is a viable option for petrol engine applications.

6. Electric Turbochargers

An electric turbocharger is used to eliminate turbo lag and to assist a normal turbocharger at lower engine speeds where a traditional turbocharger is not most efficient. This is achieved by adding an electric motor that rotates the turbo’s compressor from the start and through the lower speeds until the power from the exhaust volume is high enough to run the turbo.

This approach makes turbo lag a thing of the past and significantly increases the speed range in which the turbo works efficiently. So far, so good. It seems that electronic turbos are the answer to all of the negative characteristics of traditional turbochargers, but there are some drawbacks.

Most are about cost and complexity, as the electric motor needs to be accommodated and powered, plus also cooled to prevent reliability issues.

FAQ

What is a Turbocharger?

A turbocharger, known as a turbo, is a turbine-driven forced induction device that increases the output of an internal combustion engine by forcing additional compressed air into the combustion chamber.

How do turbocharger work?

The turbocharger on a car applies a very similar principle to a piston engine. It uses the exhaust gas to drive a turbine. This spins an air compressor that pushes extra air (and oxygen) into the cylinders, allowing them to burn more fuel each second.

What are the types of Turbocharger?

Different types of the turbocharger:

1. Single-Turbo
2. Twin-Turbo
3. Twin-Scroll Turbo
4. Variable Geometry Turbo
5. Variable Twin Scroll Turbo
6. Electric Turbo

Scroll to Top